≪ View Page

Unterschiede

Hier werden die Unterschiede zwischen zwei Versionen angezeigt.

Link zu dieser Vergleichsansicht

Beide Seiten der vorigen RevisionVorhergehende Überarbeitung
Nächste Überarbeitung		Vorhergehende Überarbeitung
en:eingabe_der_maschinenparameter_und_konfiguration:werkzeug [2026/01/07 20:49] – neelesten:eingabe_der_maschinenparameter_und_konfiguration:werkzeug [2026/07/09 11:07] (aktuell) – [Filter Element] neelest
Zeile 1: Zeile 1:
 ====== Die module ====== ====== Die module ======
- 
-  *[[en:eingabe_der_maschinenparameter_und_konfiguration:Werkzeug:Das Werkzeug-Modul]] 
-  *[[en:eingabe_der_maschinenparameter_und_konfiguration:Werkzeug:Kreisquerschnitt]] 
-  *[[en:eingabe_der_maschinenparameter_und_konfiguration:Werkzeug:Konischer Kreisquerschnitt]] 
-  *[[en:eingabe_der_maschinenparameter_und_konfiguration:Werkzeug:Rechteckspalt]] 
-  *[[en:eingabe_der_maschinenparameter_und_konfiguration:Werkzeug:Konischer Rechteckspalt]] 
-  *[[en:eingabe_der_maschinenparameter_und_konfiguration:Werkzeug:Ringspalt]] 
-  *[[en:eingabe_der_maschinenparameter_und_konfiguration:Werkzeug:Konischer Ringspalt]] 
-  *[[en:eingabe_der_maschinenparameter_und_konfiguration:Werkzeug:Filtermedium]] 
  
 ===== Die Module ===== ===== Die Module =====
Zeile 51: Zeile 42:
  
 //Configuration > Save tool as...// //Configuration > Save tool as...//
 +
 +Further details about the calculation of dies is given in the reference manual (s. [[en:grundlagenhandbuch:werkzeug:grossflaechenschmelzefilter#die|die]]).
  
 **Graphical representation of the results** **Graphical representation of the results**
Zeile 59: Zeile 52:
  
 The triangle drawn below the diagram symbolises the scroll tip. While a rectangular gap is represented by a conventional rectangle, a rectangle with a dashed line illustrates a circular cross-section. Ring gaps are indicated by a rectangle with hatched stripes in the middle, and all conical elements are represented by the changing diameter. A filter medium is described by a double-hatched area. The triangle drawn below the diagram symbolises the scroll tip. While a rectangular gap is represented by a conventional rectangle, a rectangle with a dashed line illustrates a circular cross-section. Ring gaps are indicated by a rectangle with hatched stripes in the middle, and all conical elements are represented by the changing diameter. A filter medium is described by a double-hatched area.
 +
 +===== Tube Element =====
 +
 +For the die element tube element length and diameter have to be indicated in mm. The amount indicates how many parallel elements exist in the die.
 +
 +{{ :en:eingabe_der_maschinenparameter_und_konfiguration:werkzeug:en_sigma150_dlg_eingabe_der_maschinenparameter_und_konfiguration_werkzeug_002.png?nolink |}}
 +
 +===== Conically shaped Tube Element =====
 +
 +Similarly to the geometry of the tube element again length and diameter have to be indicated. The diameters should vary with the conically-shaped tube element. Therefore they are indicated in the dialogue fields diameter inlet (D) and diameter to the outlet (d). The amount indicates how many parallel elements exist in the die.
 +
 +{{ :en:eingabe_der_maschinenparameter_und_konfiguration:werkzeug:en_sigma150_dlg_eingabe_der_maschinenparameter_und_konfiguration_werkzeug_003.png?nolink |}}
 +
 +===== Rectangular Element =====
 +
 +This element is defined by the sizes length, height and width. The amount defines how many parallel elements exist in the die.
 +
 +{{ :en:eingabe_der_maschinenparameter_und_konfiguration:werkzeug:en_sigma150_dlg_eingabe_der_maschinenparameter_und_konfiguration_werkzeug_004.png?nolink |}}
 +
 +===== Conically shaped Rectangular Element =====
 +
 +In this dialogue length and width for each the inlet and the outlet have to be indicated. Again the length of the die and the amount of parallel elements has to be indicated.
 +
 +{{ :en:eingabe_der_maschinenparameter_und_konfiguration:werkzeug:en_sigma150_dlg_eingabe_der_maschinenparameter_und_konfiguration_werkzeug_005.png?nolink |}}
 +
 +===== Annular Element =====
 +
 +This geometry needs an internal and an external diameter. The length and the amount of parallel elements have to be indicated, too.
 +
 +{{ :en:eingabe_der_maschinenparameter_und_konfiguration:werkzeug:en_sigma150_dlg_eingabe_der_maschinenparameter_und_konfiguration_werkzeug_006.png?nolink |}}
 +
 +===== Conically shaped Annular Element =====
 +
 +Like with all conically-shaped geometries the internal and the external diameter for the inlet and the outlet have to be indicated separately. The indication of length and the amount of parallel elements is also necessary.
 +
 +{{ :en:eingabe_der_maschinenparameter_und_konfiguration:werkzeug:en_sigma150_dlg_eingabe_der_maschinenparameter_und_konfiguration_werkzeug_007.png?nolink |}}
 +
 +===== Filter Element =====
 +
 +In order to calculate the pressure loss with a filter the filter area, the mesh size, the amount of elements and different reference parameters have to be indicated. The latter are known from practical tests. These are the decrease in pressure which was measured at a reference mass flow and a reference mass temperature. The reference values as well as the decrease in pressure to be calculated refer to a constant mesh size.
 +
 +{{ :en:eingabe_der_maschinenparameter_und_konfiguration:werkzeug:en_sigma150_dlg_eingabe_der_maschinenparameter_und_konfiguration_werkzeug_008.png?nolink |}}
 +
 +Futher details about the calculation of filter elements is given in the reference manual (s. [[en:grundlagenhandbuch:werkzeug:grossflaechenschmelzefilter#large-area_melt_filter|Large-area Melt Filter]]).
 +