Unterschiede

Hier werden die Unterschiede zwischen zwei Versionen angezeigt.

--- en:eingabe_der_verfahrensparameter:eingabe_der_verfahrensparameter [2025/01/13 16:21] – [Pressure at the screw tip] neelest
+++ en:eingabe_der_verfahrensparameter:eingabe_der_verfahrensparameter [2026/09/17 09:24] (aktuell) – gelöscht - Externe Bearbeitung (Unbekanntes Datum) 127.0.0.1
@@ Zeile 1: / Zeile 1: @@
-======Define process parameters  ======
-In REX/PSI Next Generation, the process parameters are defined centrally via the menu //Simulation// > //Process parameters//. These settings are crucial for the precise calculation of the processes, as they have a direct influence on the quality of the simulation. The following section describes the input options for the process-relevant parameters.
-=====Structure of the dialogue=====
-The dialogue for the process parameters is divided into two columns, each of which contains different categories of input values:
-      * **Required parameters:** These values must be specified by the user as they are essential for the calculation.
-      * **Optional parameters:** These values can be specified by the user, but are not mandatory. If these values are not entered, they are calculated automatically by the software. An example of this are parameters such as the dosing time or the location of the melt vortex formation (OSW).
-      * **PSI only**: Inputs for cycle time calculation
-       * **Only PSI**: Inputs for calculating the closing time of the non-return valve
-This subdivision allows the user to control necessary process parameters manually, while less critical values can be determined automatically by the software, which increases user-friendliness.
-===== Necessary inputs =====
-{{ :eingabe_der_verfahrensparameter:rex171_verf_en_001.png?nolink |}}
-====Calculation mode: Peripheral speed or throughput====
-First of all, the dialogue offers a choice between two calculation modes:
-      * **Circumferential speed:** The circumferential speed or the screw speed is specified. The mass throughput is calculated as a function of this.
-      * **Throughput:** Alternatively, the desired mass throughput can be specified. In this case, the speed at which the specified throughput is achieved is calculated.
-**Note:** With the optional parameters, a mass throughput can be specified in addition to the circumferential speed/rotational speed.
-====Pressure at the screw tip====
-A key function of the dialogue concerns the pressure input at the screw tip, which can be controlled in various ways depending on the process requirements. The user has three options to choose from:
-      * **Default:** If //Default// is activated, the user specifies a fixed back pressure that is used as a constant input for the simulation process. This option is suitable for standard processes in which a fixed pressure is assumed at the screw tip.
-      * **Tool:** Here, the calculation can be carried out using a [[en:eingabe_eines_werkzeugs:eingabe_eines_werkzeugs_mit_geometriedaten|backed tool]]. This method uses specific tool data to determine the pressure curve in the simulation process.
-      * **Tool characteristic curve:** This option activates the calculation of the pressure based on a [[en:eingabe_eines_werkzeugs:eingabe_einer_werkzeugkennlinie|tool_characteristic curve]]. The mould characteristic curve represents a mathematical description of the pressure curve as a function of throughput and speed, which enables precise simulation of the pressure build-up in specific moulds. This method is particularly suitable for complex moulds and variable process conditions.
-**Note:** The selection of the options //mould// and //mould characteristic// is only available in REX.
-====Pressure at the front edge of the hopper====
-In addition to the pressure at the screw tip, the pressure at the front edge of the hopper must also be specified. This is normally 1 bar and therefore ambient pressure. However, higher pressures can also be specified; this is particularly relevant for melt extruders. The pressure at the front edge of the hopper may be higher than the pressure at the screw tip.
-==== Melt temperature ====
-The input of the melt temperature represents the melt temperature at the screw tip. The input is necessary so that an initial temperature profile is available for the [[en:berechnungen:durchsatz|throughput calculation]]. \\
-The entered melt temperature therefore has an influence on the throughput calculation. However, the mass temperature can be iterated as part of the [[en:berechnungen:einfache_berechnung|calculation_settings]]. In this case, the input is required as an initial estimated value, but has no influence on the calculated throughput.
-The value therefore has an influence on the throughput calculation, but not indirectly on the temperature calculation. The temperature at the screw tip is **calculated** depending on the calculated throughput and **does not** correspond to the entered value.
-==== Raw material inlet temperature ====
-The raw material inlet temperature corresponds to the temperature at which the plastic is fed into the extruder/injection moulding machine. The temperature normally corresponds to the room temperature or the outlet temperature from a pellet dryer. \\ If a temperature above the melting temperature ($T_K/T_G$) is entered, the system is regarded as a melt extruder and no melting and melting calculation takes place.
-===== Optional entries =====
-The following entries are optional. If the fields are empty, all values are calculated as usual. If values are specified, these are used for the calculation.
-{{ :eingabe_der_verfahrensparameter:rex171_verf_en_002.png?nolink |}}
-==== Location of the melt vortex formation ====
-The location of the melt vortex formation can be specified. In this case, the melting and temperature calculation starts from the specified location.
-==== Disperse melting from ====
-REX can calculate the [[en:berechnungen:aufschmelzverlauf|melting]] in the conventional way (Maddok model) or using a disperse melting model. Dispersive melting always starts with shear and mixing elements as well as wave zones. The change from the conventional melting model to the disperse melting model can be set to an **earlier** point using the optional input made possible here.
-==== Throughput (at a specified speed) ====
-If a circumferential speed or a screw speed is specified, a throughput can also be specified here as an option. This skips the throughput calculation and the entered value is used.
-====Kennlinienfeld====
-Clicking on the ‘Characteristic curve field’ button opens a new window.
-{{ :eingabe_der_verfahrensparameter:rex171_verf_en_003.png?nolink |}}
-The characteristic curve field calculation can be activated here. Three pressures and three speeds are entered. In a process calculation, the throughput is calculated for each combination of pressures and speeds (thus for 9 operating points) so that the influence of speed and back pressure can be displayed in a diagram (see  [[en:grafische_darstellung_der_ergebnisse:kennlinienfeld|Graphical representation of the characteristic_curve_field]]).
-===== Cycle time calculation (PSI) =====
-The cycle time calculation is treated separately
-  *  cycle time calculation
-===== Inputs for calculating the closing time of the non-return valve =====
-The 3 inputs are only used to calculate the closing time of the ring non-return valve.
-  * The injection pressure must be specified. The injection pressure is one of the forces that presses the locking ring against the locking tip. A [[en:eingabe_eines_werkzeugs:eingabe_eines_werkzeugs_psi|tool/nozzle_backpressure]] is also required as a counterpart to the injection pressure.
-  * Holding pressure
-  * Holding pressure time
-The holding pressure and holding pressure time are not absolutely necessary. They are only required if the locking ring of the ring non-return valve closes after the injection phase and therefore within the holding pressure phase. This is not a sensible operating point.